Search
Products
    Menu Close

    EPISODE - 150W PER CHANNEL, 2 CHANNELS 70 VOLT DIGITAL POWER AMPLIFIER (IR, RS232, & IP CONTROL)

    Manufacturer: Picture for manufacturer Episode Electronics
    EPISODE - 150W PER CHANNEL, 2 CHANNELS 70 VOLT DIGITAL POWER AMPLIFIER (IR, RS232, & IP CONTROL)
    SKU: ESA-70V2CH-150W
    Availability:
    Richmond : 2

    Mississauga : 2
    Call for pricing

    Episode® 70V IP-Enabled Amplifier

    These 70-volt, 2-channel digital amplifiers are OvrC enabled for easy remote management, while popular control drivers, IR, IP, and RS-232 allow you to customize audio in commercial environments. It fits perfectly in restaurants, bars, or small conference rooms, and can maximize the sound of an outdoor speaker system. With four inputs and a loop out, it provides all the flexibility needed for a professional installation.

    Important Note - This amplifier is capable of 115V or 230V operation. To enable 230V operation, the installer will need to set the mechanical switch on the bottom of the unit, as well as replace the fuse on the back of the unit. Please see the manual in the support tab for further instruction.


    Episode OvrC Info banner
    Simplified Control System Integration

    Along with control drivers, this Episode® 70V Digital Amplifier can also be controlled via IR, IP, and RS-232. With the control protocol we’ve provided under the Support tab, it functions easily with any IR or serial control system and provides access to volume control, source selection and summing.

    Balanced & Unbalanced

    Most amps from the other guys force you to cut up an RCA cord to connect a standard source. Retract the razor knife and use Episode instead. This amp offers standard RCA connections for unbalanced inputs, as well as screw terminals for balanced/unbalanced inputs. Plus, an intuitive UI allows you to route inputs and outputs. So no matter what type of connection you need, you’re covered. Note: Inputs are independent by channel. If using a stereo source, you will need a Y-adapter to sum left and right RCAs into a single amp input.

    Loop Outputs

    When using a stack of amplifiers, the loop outputs are a convenient way to daisy-chain the signal to downstream components – perfect for a high power outdoor zone, for example. This eliminates the need for RCA splitters and gives a much cleaner (and faster) install.

    Gain & Volume Control

    Thanks to convenient gain controls on the UI, you can easily match input levels and prevent clipping. Plus, output level knobs allow you to adjust the volume per channel right from the UI or the amplifier itself. These controls can even be changed or disabled on the UI to avoid any customer miscues.

    Audio Sensing

    Three convenient turn-on modes make it easy to integrate with simple volume controls or sophisticated control systems right from the UI. Audio-sense is perfect for connecting to an audio source or mixer – when the source turns off, the amplifier will gracefully go into a power-saving standby mode. The 12V trigger inputs allows you to use a mixer or control system to turn the amp on or off, or have it "wake up" another device when the amp is activated.

    Part of the OvrC Ecosystem

    Adjust audio routing, input gain and output levels, and a wide variety of amplifier network settings remotely, with the help of OvrC, our signature cloud control platform. OvrC provides remote access to the local UI, where you can update firmware, modulate the amplifier gain, select inputs, set clipping levels, power-cycle the unit, or check the status and temperature of your device.

    Remote Power Cycling & Firmware Updates

    Need to reset an installed device, or upgrade to the latest firmware? Now you can do both of these things remotely in order to save valuable install time, and ensure your customer gets an efficient, fast solution for any network issues.

    Installation Flexibility

    A slim 1U (150 & 300) or 2U (500) chassis takes up less space when stacked on a shelf or installed in a rack. Included rack ears and amplifier feet give you the flexibility to install it where you need.

    ESD & Surge Protection

    We engineered this amp with high surge level protection components. During development, every connection was tested with both an ESD and lightning simulator – all speaker outputs, audio inputs, even the power input were ESD tested with up to 15,000V and surge tested at 2,400V.

    Package Contents:
    • (1) Amplifier
    • (1) Detachable 6 ft. IEC Power Cable
    • (2) Mounting Ears for Amplifier
    • (1) Installation Manual

    FEATURES

    • OvrC-enabled
    • IR, RS-232, IP, URC and Control4 drivers
    • Available in 150-, 300-, or 500-watt options

    SPECIFICATIONS

      ESA-70V2CH-150W ESA-70V2CH-300W ESA-70V2CH-500W
    Impedance Input 10KΩ/ Unbalanced, 20KΩ/ Balanced 10KΩ/ Unbalanced, 20KΩ/ Balanced 10KΩ/ Unbalanced, 20KΩ/ Balanced
    Power Output per Channel (Continuous) 150W per channel @ 70V 300W per channel @ 70V 500W per channel @ 70V
    Sensitivity Input 775mV 775mV 775mV
    Total Harmonic Distortion (THD) 0.1% THD 20 Hz-20 KHz 0.1% THD 20 Hz-20 KHz 0.1% THD 20 Hz-20 KHz
    Frequency Response 50 Hz to 20 KHz 50 Hz to 20 KHz 50 Hz to 20 KHz
    12V Trigger Input: 4.5 -12V DC; 10K Ω
    Output: 12V DC; 10mA
    Input: 4.5 -12V DC; 10K Ω
    Output: 12V DC; 10mA
    Input: 4.5 -12V DC; 10K Ω
    Output: 12V DC; 10mA
    Certifications Meets FCC Part 15, UL EN60065 Meets FCC Part 15, UL EN60065 Meets FCC Part 15, UL EN60065
    Dimensions (W x H x D) 17" x 1.73" x 14" 17" x 1.73" x 14" 17" x 3.49" x 15"
    Inputs Per Channel: 1 balanced (set screw) and 1 unbalanced RCA Per Channel: 1 balanced (set screw) and 1 unbalanced RCA Per Channel: 1 balanced (set screw) and 1 unbalanced RCA
    Operating Temperature 32°-122°F 32°-122°F 32°-122°F
    Power Consumption 400W 800W 1200W
    Line Voltage 115V AC / 230V AC 115V AC / 230V AC 115V AC / 230V AC
    Weight 11.9 lb 12.9 lb 17.4 lb
    Rack Spacing 1U 1U 2U
    Signal to Noise Ratio 95db A-weighted 95db A-weighted 95db A-weighted
    Fuse Type 115V AC: T3.15AL 250V
    230V AC: T1.6AL 250V
    115V AC: T6.3AL 250V
    230V AC: T3.15AL 250V
    115V AC: T10AL 250V
    230V AC: T5AL 250V
    Channels 2-Channel 2-Channel 2-Channel
    *
    *
    *
    Products specifications
    Control IP/IR/RS-232
    Bridgeable Yes
    Amplifier Type 70V
    Channels 2
    Watts Per Channel 101-200W
    Type Amplifiers
    Product tags